FIRST: Are you using a Minipov3 from a kit or from DIY? Make sure you mention that in your post
Minipov3 from ladyada.net
-----------------------------------------------------------------------------------------------
SECOND: What OS and computer are you using?
Windows 7 on a Macbook Pro (Dual boot, I can use either OS for this project, I am going for Windows though)
-----------------------------------------------------------------------------------------------
THIRD: Are you using a USB adapter or a serial port?
I am using the USB adapter that was suggested from ladyada.net
-----------------------------------------------------------------------------------------------
FOURTH: Did the minipov light up at all when you turned it on?
Yes, it is running through the lights one by one as I type.
-----------------------------------------------------------------------------------------------
FIFTH: What -specifically- isn't working?
I followed the instructions http://www.ladyada.net/make/minipov3/solder.html perfectly.
Default light cycle is working.
I followed the instructions http://ladyada.net/make/minipov3/software.html but got stuck.
I dont know what to call my minipov, I dont have a com1 or anything like that.
I can't figure out what my device is located. I don't have any Com1. And, where is normally shows it I have "Other devices" sub directory "USB2.0-Serial"
-----------------------------------------------------------------------------------------------
SIXTH: Post screenshots (NOT copy&paste) of what is happening
let me see here...
-----------------------------------------------------------------------------------------------
SEVENTH: Post clear, in-focus, not-blurry, easy to see photos of the top and bottom of the kit. If the photos are blurry, unfocused, and difficult to see they will only make it harder to debug what is going on
I dont have camera, but the minipov is working perfectly.
-----------------------------------------------------------------------------------------------
Please help! <3
minipov usb port com1 help
Moderators: adafruit_support_bill, adafruit
Please be positive and constructive with your questions and comments.
-
- Posts: 19
- Joined: Tue Jun 08, 2010 10:54 am
minipov usb port com1 help
- Attachments
-
- minipov usb port com1 help
- minipov ports.png (57.82 KiB) Viewed 6431 times
- adafruit_support_bill
- Posts: 88091
- Joined: Sat Feb 07, 2009 10:11 am
Re: minipov usb port com1 help
There is a yellow flag indicating a problem of some kind with your "USB2.0-Serial" device. Most likely it couldn't locate the driver for it. That's why there is no COM port.
-
- Posts: 19
- Joined: Tue Jun 08, 2010 10:54 am
Re: minipov usb port com1 help
Interesting, I did install the driver that was specifically for this usb that is also supposed to work with the minipov.There is a yellow flag indicating a problem of some kind with your "USB2.0-Serial" device. Most likely it couldn't locate the driver for it. That's why there is no COM port.
I got the usb converter and the driver link from http://www.adafruit.com/index.php?main_ ... ucts_id=18
I wonder what I can do.
- adafruit_support_bill
- Posts: 88091
- Joined: Sat Feb 07, 2009 10:11 am
Re: minipov usb port com1 help
Try right-clicking on the device in the device manager and see if it will give you a more specific error.
If it is a driver problem, it should give you the option to re-install the driver from a specific location.
I have heard that Windows 7 is a little more finicky with reagard to drivers, but I don't have any first-hand experience.
If it is a driver problem, it should give you the option to re-install the driver from a specific location.
I have heard that Windows 7 is a little more finicky with reagard to drivers, but I don't have any first-hand experience.
- opossum
- Posts: 636
- Joined: Fri Oct 26, 2007 12:42 am
Re: minipov usb port com1 help
Check the VID/PID. It may need a different driver.
http://forums.adafruit.com/viewtopic.php?p=79065#p79065
http://forums.adafruit.com/viewtopic.php?p=79065#p79065
-
- Posts: 19
- Joined: Tue Jun 08, 2010 10:54 am
Re: minipov usb port com1 help
Under hardware IDs it show the following.Check the VID/PID. It may need a different driver.
viewtopic.php?p=79065#p79065
VID_1A86&PID_7523&REV_0252
VID_1A86&PID_752
I am still unable to find the correct driver.
The USB2.0 to RS232 converter did come with a mini writable disk with no information. My problem is that my macbook pro does not take mini disks :/ so have to find the driver online.
-
- Posts: 19
- Joined: Tue Jun 08, 2010 10:54 am
Re: minipov usb port com1 help
I did try the driver from http://www.winchiphead.com/download/CH341/CH341SER.ZIP but it in German I think and the driver is completely confusing. Can anyone one help with that maybe?
I was able to get my desktop to turn on to try and see if i could make an iso or something. But, it could not copy it. So then I just tried to install it, but it is corrupted! That irritates me because it came with the USBtoSERIAL from ladyada site.
I cant find a working driver online, can anyone help!
I was able to get my desktop to turn on to try and see if i could make an iso or something. But, it could not copy it. So then I just tried to install it, but it is corrupted! That irritates me because it came with the USBtoSERIAL from ladyada site.
I cant find a working driver online, can anyone help!
-
- Posts: 12151
- Joined: Thu Apr 06, 2006 4:21 pm
Re: minipov usb port com1 help
hi please don't post in multiple threads - it makes it hard to help you if the information is in 5 places!
-
- Posts: 1
- Joined: Thu Jul 08, 2010 11:02 pm
Please be positive and constructive with your questions and comments.