Makes my head spin to look at them, but I'll give it a shot!
Thanks again for the help.
Using arduino uno, solar panel & rechargable batts
Moderators: adafruit_support_bill, adafruit
Please be positive and constructive with your questions and comments.
-
- Posts: 38
- Joined: Wed Feb 08, 2012 4:42 pm
-
- Posts: 38
- Joined: Wed Feb 08, 2012 4:42 pm
Re: Using arduino uno, solar panel & rechargable batts
Got another question about the Li-Po charger circuitry. Is it able to accept inputs from both the mini USB AND the DC jack at the same time?
Looking at adding the ability to have supplemental panels via the DC jack while wiring in my primary panels with the mini USB cable.
Suggestions?
Looking at adding the ability to have supplemental panels via the DC jack while wiring in my primary panels with the mini USB cable.
Suggestions?
- adafruit_support_bill
- Posts: 88154
- Joined: Sat Feb 07, 2009 10:11 am
Re: Using arduino uno, solar panel & rechargable batts
It is fine for the charger, but you need to make sure your panels are protected. If the panels are mis-matched, or one panel becomes 'shaded', power from the other one can back up through it. At best it will be horribly inefficient. At worst, it can damage the panel. Best to do a bit of research before you start connecting multiple panels.Looking at adding the ability to have supplemental panels via the DC jack while wiring in my primary panels with the mini USB cable.
-
- Posts: 38
- Joined: Wed Feb 08, 2012 4:42 pm
Re: Using arduino uno, solar panel & rechargable batts
It is fine for the charger, but you need to make sure your panels are protected.
Understand what you mean, for the most part. Found this article, explains a lot. http://www.solar-facts.com/panels/panel-diodes.php.
My design revolves around wiring "identical" panels in parallel to each other. Is this still a concern with individual panels being shaded? Also, between the panels and the charging circuit, do I need to include some sort of diode if I plan on using both input ports at once?
Thanks again for the insight!
Understand what you mean, for the most part. Found this article, explains a lot. http://www.solar-facts.com/panels/panel-diodes.php.
My design revolves around wiring "identical" panels in parallel to each other. Is this still a concern with individual panels being shaded? Also, between the panels and the charging circuit, do I need to include some sort of diode if I plan on using both input ports at once?
Thanks again for the insight!
- adafruit_support_bill
- Posts: 88154
- Joined: Sat Feb 07, 2009 10:11 am
Re: Using arduino uno, solar panel & rechargable batts
Yes. If panels are wired in parallel, you should add blocking diodes. If they are wired in series, you should use bypass diodes.Is this still a concern with individual panels being shaded?
-
- Posts: 38
- Joined: Wed Feb 08, 2012 4:42 pm
Re: Using arduino uno, solar panel & rechargable batts
One additional input I am considering is a Joule Thief-style charger via AA/AAA batteries, as recently featured on Hack A Day http://rayshobby.net/?page_id=1383.
Two part question. I notice on the LiPo board there is one additional DC IN next to the Mini USB. If I wire the AA/AAA Joule Thief to this input (or similar connector: USB/DC), will it appropriately transfer what's left from the AA/AAA to the LiPo via the charging circuit? I'm not quite sure how to work out how the small amounts of power left in the AA/AAA will affect the circuit overall and subsequently the charging of the LiPo (specifically the required voltage).
SEEMS like it should work since you can regulate the output onboard between 3.3 and 5v.
What do we think? Thanks in advance for the help!
Two part question. I notice on the LiPo board there is one additional DC IN next to the Mini USB. If I wire the AA/AAA Joule Thief to this input (or similar connector: USB/DC), will it appropriately transfer what's left from the AA/AAA to the LiPo via the charging circuit? I'm not quite sure how to work out how the small amounts of power left in the AA/AAA will affect the circuit overall and subsequently the charging of the LiPo (specifically the required voltage).
SEEMS like it should work since you can regulate the output onboard between 3.3 and 5v.
What do we think? Thanks in advance for the help!
- adafruit_support_bill
- Posts: 88154
- Joined: Sat Feb 07, 2009 10:11 am
Re: Using arduino uno, solar panel & rechargable batts
It you set the output to 5v, it should be able to transfer some of the remaining AA charge into the LiPo. Just don't connect it at the same time as the USB.
-
- Posts: 38
- Joined: Wed Feb 08, 2012 4:42 pm
Re: Using arduino uno, solar panel & rechargable batts
Is this a precaution because of energy flowing back into the extra device or the LiPo circuit itself? I believe we've discussed elsewhere that you can have both multiple inputs as long you have the appropriate diodes in place for back flow.It you set the output to 5v, it should be able to transfer some of the remaining AA charge into the LiPo. Just don't connect it at the same time as the USB.
Also, after speaking with the developer of the AASaver, he suggested that limiting the LiPo circuit to 100mA would be more efficient while transferring whatever juice is left in the AA/AAAs. Any insight into this? I planned on wiring in the additional 1000ohm resistor to bump the charging circuit up to 1000mA from 500mA.
-
- Posts: 38
- Joined: Wed Feb 08, 2012 4:42 pm
Re: Using arduino uno, solar panel & rechargable batts
In regards to the information regarding adding a new resistor, are we removing the on-board resistor in place by desoldering from PROG? The guide speaks of soldering OVER the in place resistor, so I assume this would be the case.
http://ladyada.net/products/usbdcsolarlipo/use.html
http://ladyada.net/products/usbdcsolarlipo/use.html
- adafruit_support_bill
- Posts: 88154
- Joined: Sat Feb 07, 2009 10:11 am
Re: Using arduino uno, solar panel & rechargable batts
It is so you don't have two voltage regulators trying to regulate the same circuit.Is this a precaution because of energy flowing back into the extra device or the LiPo circuit itself?
The formula for the programming resistor is based on the total resistance. If you solder one in parallel with the existing resistor, you need to calculate the effective total resistance = (R1 * R2) / (R1 + R2)In regards to the information regarding adding a new resistor, are we removing the on-board resistor in place by desoldering from PROG? The guide speaks of soldering OVER the in place resistor, so I assume this would be the case.
-
- Posts: 38
- Joined: Wed Feb 08, 2012 4:42 pm
Re: Using arduino uno, solar panel & rechargable batts
Understood. Thanks again for all of your help.
-
- Posts: 1
- Joined: Thu May 09, 2013 5:56 am
Re: Using arduino uno, solar panel & rechargable batts
i want to ask,,,, my project automatic cut off by solar system...when noon,charge the battery and during night battery supply to load (lamp)...can anybody help....i use the photocell sensor
Please be positive and constructive with your questions and comments.