i had two lsm 3003 connect to two separated board off FLora . One suddenly stop working , any idea what could has happend.
power ,3.3v is ok but no reaction on any sketch?
lsm3003 conntect to flora board
Moderators: adafruit_support_bill, adafruit
Please be positive and constructive with your questions and comments.
- adafruit_support_rick
- Posts: 35092
- Joined: Tue Mar 15, 2011 11:42 am
Re: lsm3003 conntect to flora board
Please post clear, detailed pictures of the Flora and LSM303, showing your soldering and connections
- AV_Wizard
- Posts: 8
- Joined: Wed Sep 11, 2013 10:20 am
Re: lsm3003 conntect to flora board
I have a BLE from redbearlab next to it , who on the same element and was working .
Sorry Adafruit , is this a support ? I'm willing to send the boards directley back to you and bay new ones .. but this is already one week going ... without any result .
- adafruit_support_bill
- Posts: 88138
- Joined: Sat Feb 07, 2009 10:11 am
Re: lsm3003 conntect to flora board
???? We responded to your initial question within hours, and 5 days later you post photos of an unrelated problem. We do our best to help, but we need your input too.Sorry Adafruit , is this a support ? I'm willing to send the boards directley back to you and bay new ones .. but this is already one week going ... without any result .
Did you figure out the problem with the LSM3003?
What specifically is the issue with the Bluefruit? More details about your system would be helpful.
- AV_Wizard
- Posts: 8
- Joined: Wed Sep 11, 2013 10:20 am
Re: lsm3003 conntect to flora board
Very basic topic
what can i do more , i received some boards , at first like most common sence peopel i gook it up to the most basic board ;..a Uno .
With all respect , i never got it working with a uno board . What can i tell more ?
I have a simular setup for some Redbear boards , in tx , rx over blue tooth , no issue , it's all working .
But with the Bluetooth and lsm 3003 i could not hook them up in a basic setup . IS some thing happend in transport ? in the same package i had some flora boards ans another lsm 3003 . They are work well ?
what can i do more , i received some boards , at first like most common sence peopel i gook it up to the most basic board ;..a Uno .
With all respect , i never got it working with a uno board . What can i tell more ?
I have a simular setup for some Redbear boards , in tx , rx over blue tooth , no issue , it's all working .
But with the Bluetooth and lsm 3003 i could not hook them up in a basic setup . IS some thing happend in transport ? in the same package i had some flora boards ans another lsm 3003 . They are work well ?
- adafruit_support_rick
- Posts: 35092
- Joined: Tue Mar 15, 2011 11:42 am
Re: lsm3003 conntect to flora board
Those are cold solder joints on your BLE board. Please reheat them. Make sure to heat the pad as well as the pin. A good solder joint will be smooth and shiny and have a concave section, like this:
In particular, I can see the solder pad on your GND connection. But all of the solder is balled up on the pins and hasn't flowed onto the pads.
In particular, I can see the solder pad on your GND connection. But all of the solder is balled up on the pins and hasn't flowed onto the pads.
- AV_Wizard
- Posts: 8
- Joined: Wed Sep 11, 2013 10:20 am
Re: lsm3003 conntect to flora board
ok will do for the second time
thansk
thansk
- AV_Wizard
- Posts: 8
- Joined: Wed Sep 11, 2013 10:20 am
Re: lsm3003 conntect to flora board
Hallo rick
i did this resoldering with a weller , 380° eact
check ic voltage off 3.3v on the pins itself ... and all is there execpt any bluetooth reaction ..
what's next
i did this resoldering with a weller , 380° eact
check ic voltage off 3.3v on the pins itself ... and all is there execpt any bluetooth reaction ..
what's next
- adafruit_support_rick
- Posts: 35092
- Joined: Tue Mar 15, 2011 11:42 am
Re: lsm3003 conntect to flora board
What is printed in Serial Monitor when you run the echodemo example sketch? can you post the complete output?
- AV_Wizard
- Posts: 8
- Joined: Wed Sep 11, 2013 10:20 am
Re: lsm3003 conntect to flora board
For the nRF8001
"Adafruit Bluefruit Low Energy nRF8001 Callback Echo demo"
for the lsm3003
nothing ...
"Adafruit Bluefruit Low Energy nRF8001 Callback Echo demo"
for the lsm3003
nothing ...
- adafruit_support_rick
- Posts: 35092
- Joined: Tue Mar 15, 2011 11:42 am
Re: lsm3003 conntect to flora board
Please post updated pictures of your soldering and connections to the nRF8001
- AV_Wizard
- Posts: 8
- Joined: Wed Sep 11, 2013 10:20 am
Re: lsm3003 conntect to flora board
i must say , that i find adafruit a great company on finding new products , but the support is not what i expected.
I,m a hoppy maker pure nature , but on the support side i ,m disappointed.
two items who did not work when i received them and endless mails about soldering and pictures is a bit to much
i hope this will change in the future .
regards
I,m a hoppy maker pure nature , but on the support side i ,m disappointed.
two items who did not work when i received them and endless mails about soldering and pictures is a bit to much
i hope this will change in the future .
regards
- adafruit_support_bill
- Posts: 88138
- Joined: Sat Feb 07, 2009 10:11 am
Re: lsm3003 conntect to flora board
We are sorry you are disappointed. It is difficult to diagnose a problem we cannot see. And even more difficult without any answers to questions we ask.
Please be positive and constructive with your questions and comments.