Wearables
Moderators: adafruit_support_bill, adafruit
Please be positive and constructive with your questions and comments.
-
- Topics
- Replies
- Views
- Last post
-
-
Conductive Rubber sheet change when wet?
- 3 Replies
- 202 Views
- Last post by millercommamatt
-
Epic results with Monster Mask!
- 11 Replies
- 207 Views
- Last post by Kiwipuzzle
-
Which kit is this?
- 1 Replies
- 54 Views
- Last post by adafruit_support_carter
-
32u4 Feather I/O pin limitation
- 3 Replies
- 54 Views
- Last post by mikeysklar
-
Advice on Adafruit hardware to purchase
- 7 Replies
- 186 Views
- Last post by RKirk
-
Help with Eragon Dragon Egg
- 21 Replies
- 410 Views
- Last post by Actordiver
-
Illuminating gaps in gauntlet
- 2 Replies
- 43 Views
- Last post by jittery
-
Gemma M0 burn bootloader problem
- 1 Replies
- 75 Views
- Last post by mikeysklar
-
Flora Board Code Not Persisting When Unplugged
- 1 Replies
- 50 Views
- Last post by bidrohini1
-
Nerf Impact Vest
- 5 Replies
- 126 Views
- Last post by mikeysklar
-
Flora V3 + SD card module
- 1 Replies
- 257 Views
- Last post by adafruit_support_mike
-
Replacing Gemma M0 circuitpy files
- 4 Replies
- 507 Views
- Last post by dastels
-
Gemma M0 works.. sometimes
- 1 Replies
- 843 Views
- Last post by adafruit_support_carter
-
Velostat pressure maximum
- 3 Replies
- 872 Views
- Last post by adafruit_support_bill
-
Flora GPS
- 7 Replies
- 934 Views
- Last post by dastels
-
Gemma v2 not working
- 6 Replies
- 644 Views
- Last post by Franklin97355
-
Gemma M0 with NAU7802 - small int overflow
- 2 Replies
- 509 Views
- Last post by devhyfes
-
Nylon Fabric Squares with Conductive Adhesive (ID 4762)
- 0 Replies
- 511 Views
- Last post by vhanson14
-
Neopixel RGBW led suit
- 2 Replies
- 629 Views
- Last post by Skoozy
-
Troubleshooting Flora + AAA JST Battery Holder
- 6 Replies
- 666 Views
- Last post by mikeysklar
-
Conductive Rubber Sheet / Stretch Sensor- Product ID: 5464.
- 0 Replies
- 589 Views
- Last post by Farhana89
-
Animated Eyes Project Customization Question
- 4 Replies
- 1115 Views
- Last post by christomato
-
GUIGGEN HAT ?
- 1 Replies
- 748 Views
- Last post by mikeysklar
-
Newbie looking for some advice
- 1 Replies
- 1084 Views
- Last post by michaelmeissner
-
Cannot receive data from BNO085 IMU in Arduino I2C mode
- 3 Replies
- 972 Views
- Last post by adafruit_support_bill
-
Unable to remove battery from JST connector
- 10 Replies
- 1145 Views
- Last post by adafruit2
-
BNO08x I2C implementation violates the I2C protocol in some circumstances
- 2 Replies
- 834 Views
- Last post by gammaburst
-
Monster M4sk movement controls?
- 5 Replies
- 903 Views
- Last post by dastels
-
Windows 11 doesnt seem to see Flora
- 1 Replies
- 744 Views
- Last post by mikeysklar
-
monster M4SK availability
- 10 Replies
- 1159 Views
- Last post by lamynsem
-
Monster M4sk - Birdlike Eyes?
- 0 Replies
- 779 Views
- Last post by artistic_thingem
-
Accelerometer for Watch?
- 1 Replies
- 800 Views
- Last post by mikeysklar
-
Fall detection using IMU
- 1 Replies
- 840 Views
- Last post by barshatriplee
-
Adafruit BNO055 - IMU Calibration
- 2 Replies
- 880 Views
- Last post by KalmanDorm39
-
IMU setup (newbie question)
- 3 Replies
- 817 Views
- Last post by Ed_23
-
Micro Controller Question
- 2 Replies
- 880 Views
- Last post by michaelmeissner
-
FLORA Accelerometer
- 1 Replies
- 774 Views
- Last post by dastels
-
Gemma m0 completely dead on arrival
- 8 Replies
- 943 Views
- Last post by adafruit_support_carter
-
trouble with gemma m0 project
- 31 Replies
- 1948 Views
- Last post by dastels
-
chirping plush owl gemma m0
- 2 Replies
- 782 Views
- Last post by hippyhillary
-
High drain compact wireless sound enabled LED
- 11 Replies
- 1044 Views
- Last post by adafruit_support_bill
-
CODE PROBLEM WITH buzzing-mindfulness-bracelet PROJECT
- 4 Replies
- 917 Views
- Last post by EmaxMartino
-
Inductive Charging
- 5 Replies
- 889 Views
- Last post by adafruit_support_bill
-
LED Sequins not working on dress?
- 5 Replies
- 895 Views
- Last post by adafruit_support_bill
-
Pulse sensor (Product ID: 1093) output
- 13 Replies
- 1080 Views
- Last post by adafruit_support_bill
-
Select using 3 M4SK buttons not working
- 1 Replies
- 770 Views
- Last post by dastels
-
Need help selecting right adafruit parts
- 1 Replies
- 788 Views
- Last post by mikeysklar
-
Adhesive for silicone-wrapped strips
- 1 Replies
- 726 Views
- Last post by adafruit_support_bill
-
Flora not connecting to USB port
- 2 Replies
- 931 Views
- Last post by EdgarBoyd
Please be positive and constructive with your questions and comments.
-