Wearables
Moderators: adafruit_support_bill, adafruit
Please be positive and constructive with your questions and comments.
-
- Topics
- Replies
- Views
- Last post
-
-
Conductive Rubber sheet change when wet?
- 3 Replies
- 104 Views
- Last post by millercommamatt
-
Epic results with Monster Mask!
- 11 Replies
- 205 Views
- Last post by Kiwipuzzle
-
Which kit is this?
- 1 Replies
- 50 Views
- Last post by adafruit_support_carter
-
32u4 Feather I/O pin limitation
- 3 Replies
- 52 Views
- Last post by mikeysklar
-
Advice on Adafruit hardware to purchase
- 7 Replies
- 185 Views
- Last post by RKirk
-
Help with Eragon Dragon Egg
- 21 Replies
- 408 Views
- Last post by Actordiver
-
Illuminating gaps in gauntlet
- 2 Replies
- 42 Views
- Last post by jittery
-
Gemma M0 burn bootloader problem
- 1 Replies
- 72 Views
- Last post by mikeysklar
-
Flora Board Code Not Persisting When Unplugged
- 1 Replies
- 46 Views
- Last post by bidrohini1
-
Nerf Impact Vest
- 5 Replies
- 123 Views
- Last post by mikeysklar
-
Flora V3 + SD card module
- 1 Replies
- 255 Views
- Last post by adafruit_support_mike
-
Replacing Gemma M0 circuitpy files
- 4 Replies
- 500 Views
- Last post by dastels
-
Gemma M0 works.. sometimes
- 1 Replies
- 840 Views
- Last post by adafruit_support_carter
-
Velostat pressure maximum
- 3 Replies
- 866 Views
- Last post by adafruit_support_bill
-
Flora GPS
- 7 Replies
- 930 Views
- Last post by dastels
-
Gemma v2 not working
- 6 Replies
- 638 Views
- Last post by Franklin97355
-
Gemma M0 with NAU7802 - small int overflow
- 2 Replies
- 503 Views
- Last post by devhyfes
-
Nylon Fabric Squares with Conductive Adhesive (ID 4762)
- 0 Replies
- 502 Views
- Last post by vhanson14
-
Neopixel RGBW led suit
- 2 Replies
- 624 Views
- Last post by Skoozy
-
Troubleshooting Flora + AAA JST Battery Holder
- 6 Replies
- 659 Views
- Last post by mikeysklar
-
Conductive Rubber Sheet / Stretch Sensor- Product ID: 5464.
- 0 Replies
- 584 Views
- Last post by Farhana89
-
Animated Eyes Project Customization Question
- 4 Replies
- 1112 Views
- Last post by christomato
-
GUIGGEN HAT ?
- 1 Replies
- 745 Views
- Last post by mikeysklar
-
Newbie looking for some advice
- 1 Replies
- 1081 Views
- Last post by michaelmeissner
-
Cannot receive data from BNO085 IMU in Arduino I2C mode
- 3 Replies
- 971 Views
- Last post by adafruit_support_bill
-
Unable to remove battery from JST connector
- 10 Replies
- 1143 Views
- Last post by adafruit2
-
BNO08x I2C implementation violates the I2C protocol in some circumstances
- 2 Replies
- 829 Views
- Last post by gammaburst
-
Monster M4sk movement controls?
- 5 Replies
- 899 Views
- Last post by dastels
-
Windows 11 doesnt seem to see Flora
- 1 Replies
- 742 Views
- Last post by mikeysklar
-
monster M4SK availability
- 10 Replies
- 1156 Views
- Last post by lamynsem
-
Monster M4sk - Birdlike Eyes?
- 0 Replies
- 777 Views
- Last post by artistic_thingem
-
Accelerometer for Watch?
- 1 Replies
- 794 Views
- Last post by mikeysklar
-
Fall detection using IMU
- 1 Replies
- 838 Views
- Last post by barshatriplee
-
Adafruit BNO055 - IMU Calibration
- 2 Replies
- 879 Views
- Last post by KalmanDorm39
-
IMU setup (newbie question)
- 3 Replies
- 816 Views
- Last post by Ed_23
-
Micro Controller Question
- 2 Replies
- 875 Views
- Last post by michaelmeissner
-
FLORA Accelerometer
- 1 Replies
- 773 Views
- Last post by dastels
-
Gemma m0 completely dead on arrival
- 8 Replies
- 942 Views
- Last post by adafruit_support_carter
-
trouble with gemma m0 project
- 31 Replies
- 1941 Views
- Last post by dastels
-
chirping plush owl gemma m0
- 2 Replies
- 779 Views
- Last post by hippyhillary
-
High drain compact wireless sound enabled LED
- 11 Replies
- 1042 Views
- Last post by adafruit_support_bill
-
CODE PROBLEM WITH buzzing-mindfulness-bracelet PROJECT
- 4 Replies
- 916 Views
- Last post by EmaxMartino
-
Inductive Charging
- 5 Replies
- 883 Views
- Last post by adafruit_support_bill
-
LED Sequins not working on dress?
- 5 Replies
- 894 Views
- Last post by adafruit_support_bill
-
Pulse sensor (Product ID: 1093) output
- 13 Replies
- 1076 Views
- Last post by adafruit_support_bill
-
Select using 3 M4SK buttons not working
- 1 Replies
- 768 Views
- Last post by dastels
-
Need help selecting right adafruit parts
- 1 Replies
- 786 Views
- Last post by mikeysklar
-
Adhesive for silicone-wrapped strips
- 1 Replies
- 725 Views
- Last post by adafruit_support_bill
-
Flora not connecting to USB port
- 2 Replies
- 930 Views
- Last post by EdgarBoyd
Please be positive and constructive with your questions and comments.
-