After changing to a 3-cell battery pack, the green LED flashes 7 times and I can't see anything from the IR bulbs in my digital camera.
Any idea what's wrong?
Thanks!
green LED flashes 7 times, no output from IR
Moderators: adafruit_support_bill, adafruit
Please be positive and constructive with your questions and comments.
- adafruit_support_rick
- Posts: 35092
- Joined: Tue Mar 15, 2011 11:42 am
Re: green LED flashes 7 times, no output from IR
It used to work with a 2-cell pack? What happens if you switch back to 2 cells?
Please post some clear, detailed pictures of the TV-B-Gone.
Please post some clear, detailed pictures of the TV-B-Gone.
- phinegan
- Posts: 3
- Joined: Wed Jan 06, 2016 6:26 pm
Re: green LED flashes 7 times, no output from IR
I get the same result with the two cell pack. What do the seven LED flashes indicate? I'm confident that my assembly of the kit is correct.
Thank you!
Thank you!
- phinegan
- Posts: 3
- Joined: Wed Jan 06, 2016 6:26 pm
Re: green LED flashes 7 times, no output from IR
I stand corrected - it works fine with the two cell battery pack but not with the three cell. I'm measuring 5.5 volts from the three cell pack - could that be excessive for the device?
- adafruit_support_rick
- Posts: 35092
- Joined: Tue Mar 15, 2011 11:42 am
Re: green LED flashes 7 times, no output from IR
The TV-B-Gone runs on 3-5V. 5.5V might be a problem
The green LED is supposed to flash every time it sends out an IR code. But in this case, it sounds like an error condition - perhaps the processor is resetting?
The green LED is supposed to flash every time it sends out an IR code. But in this case, it sounds like an error condition - perhaps the processor is resetting?
- Maze101
- Posts: 3
- Joined: Sat Jan 14, 2017 4:51 pm
Re: green LED flashes 7 times, no output from IR
I switched out the the AA battery pack for one of the 3.7V 2000 mAh Lipo's. I also included a bread board SPDT switch, a panel-ish mounted female JST for recharging, and a new taller tactile switch I replaced the original with (all stuffed in an Altoids tin).
I checked the battery voltage and its supplying 4.2V.
The green LED flashes 7 times when power is supplied and each time the tactile button is used. The device does not continue to blink like it did (For each code) when the AAs were attached.
Any idea if I fried the chip or if something else is going on?
I have not been able to determine what the 7 blinks stands for so trouble shooting is thusly limited.
Any input on what might be going on would be appreciated.
I checked the battery voltage and its supplying 4.2V.
The green LED flashes 7 times when power is supplied and each time the tactile button is used. The device does not continue to blink like it did (For each code) when the AAs were attached.
Any idea if I fried the chip or if something else is going on?
I have not been able to determine what the 7 blinks stands for so trouble shooting is thusly limited.
Any input on what might be going on would be appreciated.
- adafruit_support_rick
- Posts: 35092
- Joined: Tue Mar 15, 2011 11:42 am
Re: green LED flashes 7 times, no output from IR
Hmmm... I don't see anything in the firmware that will flash the LED 7 times. Is it a fast blink or a slow blink?
- Maze101
- Posts: 3
- Joined: Sat Jan 14, 2017 4:51 pm
Re: green LED flashes 7 times, no output from IR
It blinks approximately once every second, seven times, then stays off.
I checked the IRs with my phone and it does not appear to be firing any of them.
Update:
Was trying to avoid hacking the wiring apart, but C'est la vie....
Re-installed the 2 cell AA pack and ta-daa, worked again. Tried the Lipo directly to the board and mixed results at the moment... Likely I just don't have a secure connection for this particular test. I intend to rewire a few things later tonight, but at this time I suspect that the switch or charging port might have played a role...
Will update if I determine anything of worth. Maybe save someone else a head scratch moment...
I checked the IRs with my phone and it does not appear to be firing any of them.
Update:
Was trying to avoid hacking the wiring apart, but C'est la vie....
Re-installed the 2 cell AA pack and ta-daa, worked again. Tried the Lipo directly to the board and mixed results at the moment... Likely I just don't have a secure connection for this particular test. I intend to rewire a few things later tonight, but at this time I suspect that the switch or charging port might have played a role...
Will update if I determine anything of worth. Maybe save someone else a head scratch moment...
- adafruit_support_rick
- Posts: 35092
- Joined: Tue Mar 15, 2011 11:42 am
Re: green LED flashes 7 times, no output from IR
The firmware will slow blink like that on a brownout, but it will only blink twice.. You could be seeing a startup blink and then three brownouts.. I don't know.
Please be positive and constructive with your questions and comments.