XBee Pro Module error number of red

XBee projects like the adapter, xBee tutorials, tweetawatt/wattcher, etc. from Adafruit

Moderators: adafruit_support_bill, adafruit

Please be positive and constructive with your questions and comments.
Locked
User avatar
Adichip
 
Posts: 7
Joined: Sun Mar 30, 2014 11:16 pm

XBee Pro Module error number of red

Post by Adichip »

Dear good afternoon , I have problems with one of the XBee ( 40c673df ) purchased from you
XBee Pro Module - ZB Series 2SC - 63MW with Wire Antenna - XBP24CZ7WIT - 004
I have to reset it to communicate and then set it .... Then to configure , do not take me the number of red.-

Please can you help me with this problem ?.

Thank you

User avatar
adafruit_support_rick
 
Posts: 35092
Joined: Tue Mar 15, 2011 11:42 am

Re: XBee Pro Module error number of red

Post by adafruit_support_rick »

Please post clear, detailed pictures of your soldering and wiring

User avatar
Adichip
 
Posts: 7
Joined: Sun Mar 30, 2014 11:16 pm

Re: XBee Pro Module error number of red

Post by Adichip »

First of all I thank you for your attention.

The assembly is next, I tried everything to make it work and I have no luck. Probe examples of the manufacturer's website but seems to have a problem with the module.

I would like to see if they can give me an example with the following:

1) Coordinator, which has enabled a digital output to refresh the input status of the Router.

2) Router, which has enabled a digital input.

With an example so you could try directly upload files to open with the X-CTU and this load on each Xbee.

To rule out serious the problem is the software.

Thank you very much in advance.

Best regards.
Attachments
ebhlaplibedoclnf.png
ebhlaplibedoclnf.png (228.76 KiB) Viewed 2603 times

User avatar
adafruit_support_rick
 
Posts: 35092
Joined: Tue Mar 15, 2011 11:42 am

Re: XBee Pro Module error number of red

Post by adafruit_support_rick »

You need a resistor on that LED. Otherwise, it is a direct short circuit to ground, which will damage the pin on the XBee.

Have you configured the XBees for pin-passing in X-CTU?

User avatar
Adichip
 
Posts: 7
Joined: Sun Mar 30, 2014 11:16 pm

Re: XBee Pro Module error number of red

Post by Adichip »

Good morning, forgive my ignorance, I do not understand your question:

Have you configured the XBees for pin-passing in X-CTU?

You have you any example that can be used to test the modules?

Thanks in advance.


User avatar
Adichip
 
Posts: 7
Joined: Sun Mar 30, 2014 11:16 pm

Re: XBee Pro Module error number of red

Post by Adichip »

Good morning Rick, first of all I appreciate the time you're engaging my problem. I wanted to let you know that the module that you have to buy the firmware version 802.14.11: 45 and so I could figure must be updated to version 802.15.4

Any help instructive to update to this latest version modules ?

I think my problem arises from this detail.

Thank you very much and good start to the week.

Best regards.
Adichip

User avatar
adafruit_support_rick
 
Posts: 35092
Joined: Tue Mar 15, 2011 11:42 am

Re: XBee Pro Module error number of red

Post by adafruit_support_rick »

I think you're going to have to go to the Digi support forums. We don't know a lot about XBees here.
http://www.digi.com/support/forum/

Locked
Please be positive and constructive with your questions and comments.

Return to “XBee products (discontinued)”