Changelog: WipperSnapper Firmware Installer and Design Updat
Moderators: adafruit_support_bill, adafruit
Forum rules
If you're posting code, please make sure your code does not include your Adafruit IO Active Key or WiFi network credentials.
If you're posting code, please make sure your code does not include your Adafruit IO Active Key or WiFi network credentials.
- brubell
- Learn User Page
- Posts: 2010
- Joined: Fri Jul 17, 2015 10:33 pm
Changelog: WipperSnapper Firmware Installer and Design Updat
We’re back with new WipperSnapper features, exciting open-source integrations, and a fresh design language for all of IO!- freddyboomboom
- Posts: 267
- Joined: Wed Feb 16, 2022 7:55 pm
Re: Changelog: WipperSnapper Firmware Installer and Design U
FYI: The New Device page shows the QT Py ESP32-C3 board.
When clicking "Choose Board" for the QT Py ESP32-C3, it changes to a page with a big blue "Get Firmware" button. Clicking the Get Firmware button opens a new page with the web downloader, and the QT Py ESP32-C3 is not one of the four firmware options.
Also, there is no QT Py ESP32-C3 file on the Wippersnapper Releases page on Github: https://github.com/adafruit/Adafruit_Wi ... o/releases
This is all a work in progress, and little mistakes like this are going to happen.
I'm just reporting, it's not a problem for me.
I believe that the QT Py ESP32-C3 being on the New Devices page is the mistake/oversight.
If this should have been a new thread, I apologize.
When clicking "Choose Board" for the QT Py ESP32-C3, it changes to a page with a big blue "Get Firmware" button. Clicking the Get Firmware button opens a new page with the web downloader, and the QT Py ESP32-C3 is not one of the four firmware options.
Also, there is no QT Py ESP32-C3 file on the Wippersnapper Releases page on Github: https://github.com/adafruit/Adafruit_Wi ... o/releases
This is all a work in progress, and little mistakes like this are going to happen.
I'm just reporting, it's not a problem for me.
I believe that the QT Py ESP32-C3 being on the New Devices page is the mistake/oversight.
If this should have been a new thread, I apologize.
- brubell
- Learn User Page
- Posts: 2010
- Joined: Fri Jul 17, 2015 10:33 pm
Re: Changelog: WipperSnapper Firmware Installer and Design U
Thanks for reporting - we'll be pushing out a new build with the C3 soon. Had an issue getting it off the ground with our web flasher b/c it is a new chip architecture.freddyboomboom wrote:FYI: The New Device page shows the QT Py ESP32-C3 board.
When clicking "Choose Board" for the QT Py ESP32-C3, it changes to a page with a big blue "Get Firmware" button. Clicking the Get Firmware button opens a new page with the web downloader, and the QT Py ESP32-C3 is not one of the four firmware options.
Also, there is no QT Py ESP32-C3 file on the Wippersnapper Releases page on Github: https://github.com/adafruit/Adafruit_Wi ... o/releases
This is all a work in progress, and little mistakes like this are going to happen.
I'm just reporting, it's not a problem for me.
I believe that the QT Py ESP32-C3 being on the New Devices page is the mistake/oversight.
If this should have been a new thread, I apologize.
- sanvini
- Posts: 2
- Joined: Mon Jul 25, 2022 11:38 am
Re: Changelog: WipperSnapper Firmware Installer and Design Updat
WipperSnapper firmware downloads successful for QtPy-C3 but on reset, firmware goes into a continuous loop, no LED status, and can hear continuous connect/disconnect sound from the computer.
Can anyone confirm if QtPy-C3 was verified to be working when programmed from Adafruit.io add new device option?
Console log from https://adafruit.github.io/WipperSnappe ... py-esp32c3 attached
Can anyone confirm if QtPy-C3 was verified to be working when programmed from Adafruit.io add new device option?
Console log from https://adafruit.github.io/WipperSnappe ... py-esp32c3 attached
- Attachments
-
- QtPy_C3_Log.txt
- (3.19 KiB) Downloaded 5 times
- brubell
- Learn User Page
- Posts: 2010
- Joined: Fri Jul 17, 2015 10:33 pm
Re: Changelog: WipperSnapper Firmware Installer and Design Updat
Hi could you please file a bug report here: https://github.com/adafruit/Adafruit_Wi ... .md&title=sanvini wrote: ↑Mon Aug 29, 2022 11:44 pm WipperSnapper firmware downloads successful for QtPy-C3 but on reset, firmware goes into a continuous loop, no LED status, and can hear continuous connect/disconnect sound from the computer.
Can anyone confirm if QtPy-C3 was verified to be working when programmed from Adafruit.io add new device option?
Console log from https://adafruit.github.io/WipperSnappe ... py-esp32c3 attached
Thank you
Forum rules
If you're posting code, please make sure your code does not include your Adafruit IO Active Key or WiFi network credentials.
If you're posting code, please make sure your code does not include your Adafruit IO Active Key or WiFi network credentials.