Hi,
I have now tried the entire evening to detect a Adafruit Huzzah using Adafruit IO, but I only get to the "Download firmware" stage every time.
The firmware seems to go through.
I have created a guest network with only 2.4ghz.
But it does not detect it.
The yellow blink is flashing rapidly, nothing else.
IO / Wippersnapper does not detect Adafruit Huzzah32
Moderators: adafruit_support_bill, adafruit
Forum rules
If you're posting code, please make sure your code does not include your Adafruit IO Active Key or WiFi network credentials.
If you're posting code, please make sure your code does not include your Adafruit IO Active Key or WiFi network credentials.
- TimJan
- Posts: 1
- Joined: Wed Mar 01, 2023 6:25 pm
- brubell
- Learn User Page
- Posts: 2010
- Joined: Fri Jul 17, 2015 10:33 pm
Re: IO / Wippersnapper does not detect Adafruit Huzzah32
Hi TimJan,
Do you see the WIPPER drive on your computer? Within the secrets.json file - are all the credentials correct (please check for case sensitivity and verify that your IO key is correct too)
Do you see the WIPPER drive on your computer? Within the secrets.json file - are all the credentials correct (please check for case sensitivity and verify that your IO key is correct too)
- Shoggoth
- Posts: 6
- Joined: Sat Jan 14, 2023 7:28 pm
Re: IO / Wippersnapper does not detect Adafruit Huzzah32
Hello,
I have a similar problem with an Adafruit Huzzah32 V2. The board with ESP32 chip, 8MB Flash, 2MB PSRAM, and connector for external antenna.
I have two of these boards and neither will connect to Adafruit IO. When I flash them with CircuitPython, both of them connect to my wireless network and receive an IP address. When I flash them with Wippersnapper, neither will connect to wireless and the status light goes into a very slow (several seconds) blink. I assume it is a boot loop. I do not see the WIPPER drive on my computer. Any thoughts would be greatly appreciated.
I have a similar problem with an Adafruit Huzzah32 V2. The board with ESP32 chip, 8MB Flash, 2MB PSRAM, and connector for external antenna.
I have two of these boards and neither will connect to Adafruit IO. When I flash them with CircuitPython, both of them connect to my wireless network and receive an IP address. When I flash them with Wippersnapper, neither will connect to wireless and the status light goes into a very slow (several seconds) blink. I assume it is a boot loop. I do not see the WIPPER drive on my computer. Any thoughts would be greatly appreciated.
- brubell
- Learn User Page
- Posts: 2010
- Joined: Fri Jul 17, 2015 10:33 pm
Re: IO / Wippersnapper does not detect Adafruit Huzzah32
Could you open a bug report on the WipperSnapper repository: https://github.com/adafruit/Adafruit_Wi ... .md&title=Shoggoth wrote: ↑Thu Apr 06, 2023 12:33 pm Hello,
I have a similar problem with an Adafruit Huzzah32 V2. The board with ESP32 chip, 8MB Flash, 2MB PSRAM, and connector for external antenna.
I have two of these boards and neither will connect to Adafruit IO. When I flash them with CircuitPython, both of them connect to my wireless network and receive an IP address. When I flash them with Wippersnapper, neither will connect to wireless and the status light goes into a very slow (several seconds) blink. I assume it is a boot loop. I do not see the WIPPER drive on my computer. Any thoughts would be greatly appreciated.
Thanks!
- Shoggoth
- Posts: 6
- Joined: Sat Jan 14, 2023 7:28 pm
Re: IO / Wippersnapper does not detect Adafruit Huzzah32
Done.
github.com/adafruit/Adafruit_Wippersnapper_Arduino/issues/424
github.com/adafruit/Adafruit_Wippersnapper_Arduino/issues/424
- brubell
- Learn User Page
- Posts: 2010
- Joined: Fri Jul 17, 2015 10:33 pm
Re: IO / Wippersnapper does not detect Adafruit Huzzah32
Thanks, I'll take it from there!
- dobbsjs
- Posts: 3
- Joined: Sat Apr 08, 2023 12:16 am
Re: IO / Wippersnapper does not detect Adafruit Huzzah32
Hello,I just wanted to mention that I have the same issue. Thank you for taking up this issue, I will wait for any updates on this.
- brubell
- Learn User Page
- Posts: 2010
- Joined: Fri Jul 17, 2015 10:33 pm
Re: IO / Wippersnapper does not detect Adafruit Huzzah32
Tracking via this issue: https://github.com/adafruit/Adafruit_Wi ... issues/424. Please add any relevant info you have there.
Forum rules
If you're posting code, please make sure your code does not include your Adafruit IO Active Key or WiFi network credentials.
If you're posting code, please make sure your code does not include your Adafruit IO Active Key or WiFi network credentials.